Packet Tracer - Configure Initial Router Settings
Topology
Objectives
Part 1: Verify the Default Router Configuration
Part 2: Configure and Verify the Initial Router Configuration
Part 3: Save the Running Configuration File
Background
In this activity, you will perform basic router configurations. You will secure access to the CLI and console port using encrypted and plain text passwords. You will also configure messages for users logging into the router. These banners also warn unauthorized users that access is prohibited. Finally, you will verify and save your running configuration.
Part 1: Verify the Default Router Configuration
Step 1: Establish a console connection to R1.
a. Choose a Console cable from the available connections.
b. Click PCA and select RS 232.
c. Click R1 and select Console.
d. Click PCA > Desktop tab > Terminal.
e. Click OK and press ENTER. You are now able to configure R1.
Step 2: Enter privileged mode and examine the current configuration.
You can access all the router commands from privileged EXEC mode. However, because many of the privileged commands configure operating parameters, privileged access should be password-protected to prevent unauthorized use.
a. Enter privileged EXEC mode by entering the enable command.
Router> enable
Router#
Notice that the prompt changed in the configuration to reflect privileged EXEC mode.
b. Enter the show running-config command:
Router# show running-config
c. Answer the following questions:
What is the router’s hostname? _____________________________________________________________
How many Fast Ethernet interfaces does the Router have? ______________________________________
How many Gigabit Ethernet interfaces does the Router have? ____________________________________
How many Serial interfaces does the router have? _____________________________________________
What is the range of values shown for the vty lines? ____________________________________________
d. Display the current contents of NVRAM.
Router# show startup-config
startup-config is not present
Why does the router respond with the startup-config is not present message?
____________________________________________________________________________________
Part 2: Configure and Verify the Initial Router Configuration
To configure parameters on a router, you may be required to move between various configuration modes. Notice how the prompt changes as you navigate through the router.
Step 1: Configure the initial settings on R1.
Note: If you have difficulty remembering the commands, refer to the content for this topic. The commands are the same as you configured on a switch.
a. R1 as the hostname.
b. Use the following passwords:
1) Console: letmein
2) Privileged EXEC, unencrypted: cisco
3) Privileged EXEC, encrypted: itsasecret
c. Encrypt all plain text passwords.
d. Message of the day text: Unauthorized access is strictly prohibited.
Step 2: Verify the initial settings on R1.
a. Verify the initial settings by viewing the configuration for R1. What command do you use?
____________________________________________________________________________________
____________________________________________________________________________________
b. Exit the current console session until you see the following message:
R1 con0 is now available
Press RETURN to get started.
c. Press ENTER; you should see the following message:
Unauthorized access is strictly prohibited.
User Access Verification
Password:
Why should every router have a message-of-the-day (MOTD) banner?
____________________________________________________________________________________
If you are not prompted for a password, what console line command did you forget to configure?____________________________________________________________________________________
d. Enter the passwords necessary to return to privileged EXEC mode.
Why would the enable secret password allow access to the privileged EXEC mode and the enable password no longer be valid?
____________________________________________________________________________________
If you configure any more passwords on the router, are they displayed in the configuration file as plain text or in encrypted form? Explain.____________________________________________________________________________________
Part 3: Save the Running Configuration FileStep 1: Save the configuration file to NVRAM.
a. You have configured the initial settings for R1. Now back up the running configuration file to NVRAM to ensure that the changes made are not lost if the system is rebooted or loses power.
What command did you enter to save the configuration to NVRAM?
____________________________________________________________________________________
What is the shortest, unambiguous version of this command? ___________________________________
Which command displays the contents of the NVRAM?
____________________________________________________________________________________
b. Verify that all of the parameters configured are recorded. If not, analyze the output and determine which commands were not done or were entered incorrectly. You can also click Check Results in the instruction window.
Step 2: Optional bonus: Save the startup configuration file to flash.
Although you will be learning more about managing the flash storage in a router in later chapters, you may be interested to know now that —, as an added backup procedure —, you can save your startup configuration file to flash. By default, the router still loads the startup configuration from NVRAM, but if NVRAM becomes corrupt, you can restore the startup configuration by copying it over from flash.
Complete the following steps to save the startup configuration to flash.
a. Examine the contents of flash using the show flash command:
R1# show flash
How many files are currently stored in flash? __________________________________________________
Which of these files would you guess is the IOS image? ________________________________________
Why do you think this file is the IOS image?
____________________________________________________________________________________
____________________________________________________________________________________
b. Save the startup configuration file to flash using the following commands:
R1# copy startup-config flash
Destination filename [startup-config]
The router prompts to store the file in flash using the name in brackets. If the answer is yes, then press ENTER; if not, type an appropriate name and press ENTER.
c. Use the show flash command to verify the startup configuration file is now stored in flash.
Download Latihan Packet Tracert-Configure Initial Router Settings
0 komentar :
Posting Komentar